Switcheroo

Switcheroo
Identifier:	South 1-8
Area:	Southern Coast
Puzzle Type:	Main
Previous Puzzle:	Remote Interchange
Next Puzzle:	Aerial Warp

Switcheroo is the eighth main puzzle in the Southern Coast area of The Talos Principle 2.

Puzzle elements

• Blue door
• Connector
• Emitter
• Fan
• Hexahedron
• Pressure plate
• Purple barrier
• Receiver
• Teleporter

Overview

As you enter the puzzle, you find yourself in a small area with a connector on the left, a pressure plate on the right with a blue door right in front of it, followed by a purple barrier that leads into the main area of the puzzle.

In the main area, there is a red emitter on the bottom of a central tower, a fan on the ground with a pressure plate next to it, a hexahedron, and a blue door that is blocking access to the rear of the puzzle.

In the rear area, there is a teleporter and a pressure plate.

On top of the central tower, there is a blue door, and a red receiver that is somewhat inset into the floor, so that it is not easily visible from the ground.

Hints

A basic hint:

[ hint ]

Since the name of the puzzle is Switcheroo, you will have to think about how to swap the places of some equipment.

If you're struggling to get started:

[ hint ]

The first objective is to bring all the equipment to the main area. Fly up high and then bring the teleporter out, then bring the connector.

If you don't know how to reach the top of the tower:

[ hint ]

Standing on the fan stream alone is not enough. You need just a bit more elevation, then you can jump across.

If your equipment is falling off:

[ hint ]

Only the hexahedron provides a non slippery base for your equipment.

What are the rules for what equipment can go on top of what other equipment?:

[ hint ]

Connectors and teleporters can be placed on top of hexahedrons, and will maintain their positions when they fly up in the air. You can also ride along with a teleporter on top of a hexahedron. However, a connector cannot be placed on top of a teleporter that is already on top of a hexahedron. Similarly, you cannot ride on top of a connector that is already on top of a hexahedron.

If you're unable to connect the connector:

[ hint ]

First figure out a way to travel back and forth from the top of the tower without relying on the fan. Use this method of travel to finish connecting your connector. Then whenever you put the connector down, and try to pick it up again, use the alternate button that keeps the connections.

If you're stuck near the end:

[ hint ]

Don't be too hasty to keep the fan active. Notice that you can reach the pressure plate with the equipment on your hand while you're standing on top of the hexahedron when it is placed on an inactive fan. Similarly, notice that you can reach the top of the flying hexahedron from the edge of the upper floor of the tower.

Solution

[ solution ]

• 
  Step 1: Place the connector on the pressure plate to open the blue door, then walk inside.
• 
  Step 2: Place the hexahedron on the pressure plate inside to turn on the fan, then jump into the air stream. Teleport to the rear area.
• 
  Step 3: Place the teleporter on the pressure plate to open the blue door, then grab the hexahedron and bring it to the rear area.
• 
  Step 4: Replace the teleporter with the hexahedron on the pressure plate, move the teleporter out into the main area. Walk back to the rear, pick up the hexahedron, and then teleport into the main area.
• 
  Step 5: Walk back out and teleport in with the connector in your hands.
• 
  Step 6: Place the hexahedron on the fan, then the teleporter on the hex. Activate the fan with the connector, then teleport up to the air.
• 
  Step 7: Step onto the ledge on the tower, grab the teleporter, and put it on the edge.
• 
  Step 8: Jump down and grab the connector. Connect it to the emitter below, then teleport up.
• 
  Step 9: Connect the connector to the receiver as well, and place it on the ledge. Grab the teleporter and jump back down.
• 
  Step 10: Climb up on the hexahedron and place the teleporter on the pressure plate to activate the fan.
• 
  Step 11: Jump from the hex to the ledge.
• 
  Step 12: Pick up the connector, making sure to Keep Connections.
• 
  Step 13: Place it on the hexahedron from across the ledge. Don't fall down. Turn around and activate the progress wheel.

Trivia and glitches

• There is an achievement available for solving this puzzle without using the keep connections option.